[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.14.4-gnuowen (sam@judas) (gcc version 4.8.2 (Debian 4.8.2-16) ) #19 SMP PREEMPT Fri May 23 08:56:34 MDT 2014
[    0.000000] Disabled fast string operations
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000000fff] type 16
[    0.000000] BIOS-e820: [mem 0x0000000000001000-0x000000000009ffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000000c0000-0x000000003f6cffff] usable
[    0.000000] BIOS-e820: [mem 0x000000003f6d0000-0x000000003f7fffff] type 16
[    0.000000] BIOS-e820: [mem 0x000000003f800000-0x000000003fffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
[    0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: LENOVO 1703WMF/1703WMF, BIOS CBET4000 7BETC7WW (2.08 ) 06/08/2014
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x3f6d0 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-FFFFF write-back
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask 0C0000000 write-back
[    0.000000]   1 base 03F800000 mask 0FF800000 uncachable
[    0.000000]   2 base 0D0000000 mask 0F0000000 write-combining
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] PAT not supported by CPU.
[    0.000000] found SMP MP-table at [mem 0x000f0400-0x000f040f] mapped at [c00f0400]
[    0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] init_memory_mapping: [mem 0x36400000-0x367fffff]
[    0.000000]  [mem 0x36400000-0x367fffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x30000000-0x363fffff]
[    0.000000]  [mem 0x30000000-0x363fffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x2fffffff]
[    0.000000]  [mem 0x00100000-0x003fffff] page 4k
[    0.000000]  [mem 0x00400000-0x2fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x36800000-0x377fdfff]
[    0.000000]  [mem 0x36800000-0x373fffff] page 2M
[    0.000000]  [mem 0x37400000-0x377fdfff] page 4k
[    0.000000] BRK [0x017cb000, 0x017cbfff] PGTABLE
[    0.000000] RAMDISK: [mem 0x36bca000-0x375dcfff]
[    0.000000] ACPI: RSDP 000f0800 000024 (v02 CORE  )
[    0.000000] ACPI: XSDT 3f6e28e0 00004C (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: HPET 3f6e2a10 000038 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: APIC 3f6e2a50 000068 (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: MCFG 3f6e2ac0 00003C (v01 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: FACP 3f6e5d10 0000F4 (v03 CORE   COREBOOT 00000000 CORE 00000000)
[    0.000000] ACPI: DSDT 3f6e2b40 0030CA (v03 COREv4 COREBOOT 20090419 INTL 20140114)
[    0.000000] ACPI: FACS 3f6e2b00 000040
[    0.000000] ACPI: SSDT 3f6e5e10 0002FC (v02 CORE   COREBOOT 0000002A CORE 0000002A)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 126MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000] BRK [0x017cc000, 0x017ccfff] PGTABLE
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00001000-0x00ffffff]
[    0.000000]   Normal   [mem 0x01000000-0x377fdfff]
[    0.000000]   HighMem  [mem 0x377fe000-0x3f6cffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00001000-0x0009ffff]
[    0.000000]   node   0: [mem 0x00100000-0x3f6cffff]
[    0.000000] On node 0 totalpages: 259695
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3999 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 223230 pages, LIFO batch:31
[    0.000000]   HighMem zone: 254 pages used for memmap
[    0.000000]   HighMem zone: 32466 pages, LIFO batch:7
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x508
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.000000] e820: [mem 0x40000000-0xefffffff] available for PCI devices
[    0.000000] setup_percpu: NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 13 pages/cpu @f75de000 s31360 r0 d21888 u53248
[    0.000000] pcpu-alloc: s31360 r0 d21888 u53248 alloc=13*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257919
[    0.000000] Kernel command line: BOOT_IMAGE=(ahci0,1)/boot/vmlinuz-3.14.4-gnuowen root=/dev/sda1 processor.max_cstate=2 drm.debug=0x06 console=tty0 console=ttyS0,115200n8
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (000377fe:0003f6d0)
[    0.000000] Initializing Movable for node 0 (00000000:00000000)
[    0.000000] Memory: 1011284K/1038780K available (4113K kernel code, 324K rwdata, 1560K rodata, 480K init, 1448K bss, 27496K reserved, 129864K highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff8e000 - 0xfffff000   ( 452 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc15de000 - 0xc1656000   ( 480 kB)
[    0.000000]       .data : 0xc14049c3 - 0xc15dd200   (1890 kB)
[    0.000000]       .text : 0xc1000000 - 0xc14049c3   (4114 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:2304 nr_irqs:512 16
[    0.000000] CPU 0 irqstacks, hard=f6008000 soft=f600a000
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] console [ttyS0] enabled
[    0.000000] allocated 2097152 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1662.577 MHz processor
[    0.002013] Calibrating delay loop (skipped), value calculated using timer frequency.. 3325.15 BogoMIPS (lpj=1662577)
[    0.004005] pid_max: default: 32768 minimum: 301
[    0.005018] ACPI: Core revision 20131218
[    0.009316] ACPI: All ACPI Tables successfully acquired
[    0.013045] Security Framework initialized
[    0.014008] SELinux:  Disabled at boot.
[    0.015020] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.016006] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.018024] Initializing cgroup subsys memory
[    0.019009] Initializing cgroup subsys devices
[    0.020005] Initializing cgroup subsys freezer
[    0.021004] Initializing cgroup subsys net_cls
[    0.022004] Initializing cgroup subsys blkio
[    0.023004] Initializing cgroup subsys perf_event
[    0.024032] Disabled fast string operations
[    0.026008] CPU: Physical Processor ID: 0
[    0.027004] CPU: Processor Core ID: 0
[    0.028005] mce: CPU supports 6 MCE banks
[    0.029013] CPU0: Thermal monitoring enabled (TM2)
[    0.030015] Last level iTLB entries: 4KB 128, 2MB 0, 4MB 2
[    0.030015] Last level dTLB entries: 4KB 128, 2MB 0, 4MB 8, 1GB 0
[    0.030015] tlb_flushall_shift: 6
[    0.031102] Freeing SMP alternatives memory: 12K (c1656000 - c1659000)
[    0.032079] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.033464] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.044028] smpboot: CPU0: Intel(R) Core(TM) Duo CPU      L2400  @ 1.66GHz (fam: 06, model: 0e, stepping: 0c)
[    0.049000] Performance Events: Core events, core PMU driver.
[    0.051003] ... version:                1
[    0.052002] ... bit width:              40
[    0.053002] ... generic registers:      2
[    0.054002] ... value mask:             000000ffffffffff
[    0.055002] ... max period:             000000007fffffff
[    0.056002] ... fixed-purpose events:   0
[    0.057002] ... event mask:             0000000000000003
[    0.064083] CPU 1 irqstacks, hard=f62a4000 soft=f62a6000
[    0.064086] x86: Booting SMP configuration:
[    0.065004] .... node  #0, CPUs:      #1
[    0.003000] Initializing CPU#1
[    0.003000] Disabled fast string operations
[    0.086098] x86: Booted up 1 node, 2 CPUs
[    0.087004] smpboot: Total of 2 processors activated (6650.30 BogoMIPS)
[    0.090141] devtmpfs: initialized
[    0.094426] regulator-dummy: no parameters
[    0.098082] NET: Registered protocol family 16
[    0.103200] cpuidle: using governor ladder
[    0.107003] cpuidle: using governor menu
[    0.111084] ACPI: bus type PCI registered
[    0.115076] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[    0.125005] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
[    0.131002] PCI: Using MMCONFIG for extended config space
[    0.137002] PCI: Using configuration type 1 for base access
[    0.145045] bio: create slab <bio-0> at 0
[    0.146065] ACPI: Added _OSI(Module Device)
[    0.147003] ACPI: Added _OSI(Processor Device)
[    0.148002] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.149002] ACPI: Added _OSI(Processor Aggregator Device)
[    0.153757] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.155246] ACPI: Interpreter enabled
[    0.156014] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131218/hwxface-580)
[    0.159003] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131218/hwxface-580)
[    0.162019] ACPI: (supports S0 S3 S4 S5)
[    0.163002] ACPI: Using IOAPIC for interrupt routing
[    0.164038] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.165317] ACPI: ACPI Dock Station Driver: 1 docks/bays found
[    0.175770] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.176010] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.177115] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.178137] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.179053] PCI host bridge to bus 0000:00
[    0.180005] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.181004] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7]
[    0.182004] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff]
[    0.183004] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[    0.184004] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
[    0.185004] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
[    0.186004] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
[    0.187004] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff]
[    0.188004] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[    0.189004] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[    0.190004] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[    0.191004] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[    0.192004] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[    0.193004] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[    0.194004] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff]
[    0.195004] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff]
[    0.196004] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff]
[    0.197004] pci_bus 0000:00: root bus resource [mem 0x40000000-0xfebfffff]
[    0.198004] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[    0.199015] pci 0000:00:00.0: [8086:27a0] type 00 class 0x060000
[    0.199175] pci 0000:00:02.0: [8086:27a2] type 00 class 0x030000
[    0.199191] pci 0000:00:02.0: reg 0x10: [mem 0xe4300000-0xe437ffff]
[    0.199199] pci 0000:00:02.0: reg 0x14: [io  0x50a0-0x50a7]
[    0.199209] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff pref]
[    0.199218] pci 0000:00:02.0: reg 0x1c: [mem 0xe4400000-0xe443ffff]
[    0.199362] pci 0000:00:02.1: [8086:27a6] type 00 class 0x038000
[    0.199375] pci 0000:00:02.1: reg 0x10: [mem 0xe4380000-0xe43fffff]
[    0.199580] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[    0.199606] pci 0000:00:1b.0: reg 0x10: [mem 0xe4440000-0xe4443fff 64bit]
[    0.199725] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.199798] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    0.200079] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[    0.200204] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.200353] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
[    0.200476] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.201145] pci 0000:00:1c.2: [8086:27d4] type 01 class 0x060400
[    0.201263] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.201407] pci 0000:00:1c.3: [8086:27d6] type 01 class 0x060400
[    0.201522] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    0.201668] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[    0.201727] pci 0000:00:1d.0: reg 0x20: [io  0x5000-0x501f]
[    0.201836] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.202074] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[    0.202133] pci 0000:00:1d.1: reg 0x20: [io  0x5020-0x503f]
[    0.202241] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.203074] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[    0.203133] pci 0000:00:1d.2: reg 0x20: [io  0x5040-0x505f]
[    0.203241] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.204071] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[    0.204130] pci 0000:00:1d.3: reg 0x20: [io  0x5060-0x507f]
[    0.204237] pci 0000:00:1d.3: System wakeup disabled by ACPI
[    0.205087] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[    0.205117] pci 0000:00:1d.7: reg 0x10: [mem 0xe4444000-0xe44443ff]
[    0.205227] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.205295] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.206080] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
[    0.206270] pci 0000:00:1f.0: [8086:27b9] type 00 class 0x060100
[    0.206390] pci 0000:00:1f.0: address space collision: [io  0x0500-0x057f] conflicts with ACPI CPU throttle [??? 0x00000510-0x00000515 flags 0x80000000]
[    0.207009] pci 0000:00:1f.0: quirk: [io  0x0480-0x04bf] claimed by ICH6 GPIO
[    0.208006] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 1600 (mask 007f)
[    0.209005] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 15e0 (mask 000f)
[    0.210005] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 1680 (mask 001f)
[    0.211156] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
[    0.211176] pci 0000:00:1f.1: reg 0x10: [io  0x50a8-0x50af]
[    0.211191] pci 0000:00:1f.1: reg 0x14: [io  0x50c8-0x50cb]
[    0.211206] pci 0000:00:1f.1: reg 0x18: [io  0x50b0-0x50b7]
[    0.211220] pci 0000:00:1f.1: reg 0x1c: [io  0x50cc-0x50cf]
[    0.211235] pci 0000:00:1f.1: reg 0x20: [io  0x5080-0x508f]
[    0.211385] pci 0000:00:1f.2: [8086:27c5] type 00 class 0x010601
[    0.211411] pci 0000:00:1f.2: reg 0x10: [io  0x50b8-0x50bf]
[    0.211425] pci 0000:00:1f.2: reg 0x14: [io  0x50d0-0x50d3]
[    0.211439] pci 0000:00:1f.2: reg 0x18: [io  0x50c0-0x50c7]
[    0.211452] pci 0000:00:1f.2: reg 0x1c: [io  0x50d4-0x50d7]
[    0.211466] pci 0000:00:1f.2: reg 0x20: [io  0x5090-0x509f]
[    0.211481] pci 0000:00:1f.2: reg 0x24: [mem 0xe4444400-0xe44447ff]
[    0.211542] pci 0000:00:1f.2: PME# supported from D3hot
[    0.211675] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[    0.211751] pci 0000:00:1f.3: reg 0x20: [io  0x0400-0x041f]
[    0.212107] pci 0000:01:00.0: [8086:109a] type 00 class 0x020000
[    0.212141] pci 0000:01:00.0: reg 0x10: [mem 0xe4100000-0xe411ffff]
[    0.212185] pci 0000:01:00.0: reg 0x18: [io  0x4000-0x401f]
[    0.212389] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.212490] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.213021] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.214007] pci 0000:00:1c.0:   bridge window [io  0x4000-0x4fff]
[    0.214014] pci 0000:00:1c.0:   bridge window [mem 0xe4100000-0xe41fffff]
[    0.214138] pci 0000:02:00.0: [168c:002b] type 00 class 0x028000
[    0.214173] pci 0000:02:00.0: reg 0x10: [mem 0xe4200000-0xe420ffff 64bit]
[    0.214351] pci 0000:02:00.0: supports D1
[    0.214355] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold
[    0.216021] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.218005] pci 0000:00:1c.1:   bridge window [mem 0xe4200000-0xe42fffff]
[    0.218103] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.219103] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    0.220084] pci 0000:05:00.0: [1180:0476] type 02 class 0x060700
[    0.220107] pci 0000:05:00.0: proprietary Ricoh MMC controller disabled (via cardbus function)
[    0.221004] pci 0000:05:00.0: MMC cards are now supported by standard SDHCI controller
[    0.222019] pci 0000:05:00.0: reg 0x10: [mem 0xe2000000-0xe2000fff]
[    0.222060] pci 0000:05:00.0: supports D1 D2
[    0.222064] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.222104] pci 0000:05:00.0: System wakeup disabled by ACPI
[    0.223080] pci 0000:05:00.1: [1180:0552] type 00 class 0x0c0010
[    0.223106] pci 0000:05:00.1: reg 0x10: [mem 0xe2001000-0xe20017ff]
[    0.223210] pci 0000:05:00.1: supports D1 D2
[    0.223213] pci 0000:05:00.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.223313] pci 0000:05:00.2: [1180:0822] type 00 class 0x080500
[    0.223339] pci 0000:05:00.2: reg 0x10: [mem 0xe2001800-0xe20018ff]
[    0.223444] pci 0000:05:00.2: supports D1 D2
[    0.224004] pci 0000:05:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.224152] pci 0000:00:1e.0: PCI bridge to [bus 05-06] (subtractive decode)
[    0.225007] pci 0000:00:1e.0:   bridge window [io  0x2000-0x3fff]
[    0.225014] pci 0000:00:1e.0:   bridge window [mem 0xe0000000-0xe20fffff]
[    0.225025] pci 0000:00:1e.0:   bridge window [mem 0xe2100000-0xe40fffff 64bit pref]
[    0.225029] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.225034] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.225038] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.225042] pci 0000:00:1e.0:   bridge window [mem 0x000c0000-0x000c3fff] (subtractive decode)
[    0.225046] pci 0000:00:1e.0:   bridge window [mem 0x000c4000-0x000c7fff] (subtractive decode)
[    0.225051] pci 0000:00:1e.0:   bridge window [mem 0x000c8000-0x000cbfff] (subtractive decode)
[    0.225055] pci 0000:00:1e.0:   bridge window [mem 0x000cc000-0x000cffff] (subtractive decode)
[    0.225059] pci 0000:00:1e.0:   bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode)
[    0.225063] pci 0000:00:1e.0:   bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
[    0.225068] pci 0000:00:1e.0:   bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
[    0.225072] pci 0000:00:1e.0:   bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
[    0.225076] pci 0000:00:1e.0:   bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
[    0.225080] pci 0000:00:1e.0:   bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
[    0.225084] pci 0000:00:1e.0:   bridge window [mem 0x000e8000-0x000ebfff] (subtractive decode)
[    0.225089] pci 0000:00:1e.0:   bridge window [mem 0x000ec000-0x000effff] (subtractive decode)
[    0.225093] pci 0000:00:1e.0:   bridge window [mem 0x000f0000-0x000fffff] (subtractive decode)
[    0.225097] pci 0000:00:1e.0:   bridge window [mem 0x40000000-0xfebfffff] (subtractive decode)
[    0.225101] pci 0000:00:1e.0:   bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[    0.225169] pci_bus 0000:06: busn_res: can not insert [bus 06-ff] under [bus 05-06] (conflicts with (null) [bus 05-06])
[    0.225177] pci_bus 0000:06: busn_res: [bus 06-ff] end is updated to 09
[    0.225182] pci_bus 0000:06: busn_res: can not insert [bus 06-09] under [bus 05-06] (conflicts with (null) [bus 05-06])
[    0.225189] pci_bus 0000:06: [bus 06-09] partially hidden behind transparent bridge 0000:05 [bus 05-06]
[    0.226045] pci_bus 0000:00: on NUMA node 0
[    0.226166] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.230274] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.233671] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.237273] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.240674] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.244273] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.248662] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.252271] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.257155] ACPI : EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[    0.258077] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    0.259010] vgaarb: loaded
[    0.260002] vgaarb: bridge control possible 0000:00:02.0
[    0.261139] SCSI subsystem initialized
[    0.262038] libata version 3.00 loaded.
[    0.262073] PCI: Using ACPI for IRQ routing
[    0.265965] PCI: pci_cache_line_size set to 64 bytes
[    0.266062] e820: reserve RAM buffer [mem 0x3f6d0000-0x3fffffff]
[    0.266321] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.267008] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.269201] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.272027] Switched to clocksource hpet
[    0.281589] pnp: PnP ACPI init
[    0.284695] ACPI: bus type PNP registered
[    0.288859] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.295492] system 00:00: [mem 0xfed14000-0xfed17fff] has been reserved
[    0.302119] system 00:00: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.308746] system 00:00: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.315369] system 00:00: [mem 0xf0000000-0xf3ffffff] has been reserved
[    0.321997] system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.328619] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.335247] system 00:00: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.341871] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.342439] pnp 00:01: [dma 4]
[    0.342488] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.342544] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[    0.342706] system 00:03: [mem 0xfed00000-0xfed003ff] has been reserved
[    0.349335] system 00:03: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
[    0.349408] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.349500] system 00:05: [io  0x0800-0x080f] has been reserved
[    0.355434] system 00:05: [io  0x0500-0x057f] could not be reserved
[    0.361714] system 00:05: [io  0x0480-0x04bf] has been reserved
[    0.367643] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.367706] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.367784] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.367855] pnp 00:08: Plug and Play ACPI device, IDs PNP0f13 (active)
[    0.367903] pnp: PnP ACPI: found 9 devices
[    0.372017] ACPI: bus type PNP unregistered
[    0.414880] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[    0.414934] pci 0000:00:1f.0: BAR 13: [io  0x0500-0x057f] has bogus alignment
[    0.422087] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[    0.422103] pci 0000:00:1c.0: BAR 15: assigned [mem 0x40000000-0x401fffff 64bit pref]
[    0.429944] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    0.434926] pci 0000:00:1c.0:   bridge window [io  0x4000-0x4fff]
[    0.441032] pci 0000:00:1c.0:   bridge window [mem 0xe4100000-0xe41fffff]
[    0.447832] pci 0000:00:1c.0:   bridge window [mem 0x40000000-0x401fffff 64bit pref]
[    0.455592] pci 0000:00:1c.1: PCI bridge to [bus 02]
[    0.460574] pci 0000:00:1c.1:   bridge window [mem 0xe4200000-0xe42fffff]
[    0.467381] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.472376] pci 0000:00:1c.3: PCI bridge to [bus 04]
[    0.477370] pci 0000:05:00.0: res[15]=[mem 0x04000000-0x03ffffff pref] get_res_add_size add_size 4000000
[    0.477375] pci 0000:05:00.0: res[16]=[mem 0x04000000-0x03ffffff] get_res_add_size add_size 4000000
[    0.477380] pci 0000:05:00.0: res[13]=[io  0x0100-0x00ff] get_res_add_size add_size 100
[    0.477385] pci 0000:05:00.0: res[14]=[io  0x0100-0x00ff] get_res_add_size add_size 100
[    0.477399] pci 0000:05:00.0: BAR 15: assigned [mem 0x44000000-0x47ffffff pref]
[    0.484733] pci 0000:05:00.0: BAR 16: assigned [mem 0x48000000-0x4bffffff]
[    0.491621] pci 0000:05:00.0: BAR 13: assigned [io  0x2000-0x20ff]
[    0.497817] pci 0000:05:00.0: BAR 14: assigned [io  0x2400-0x24ff]
[    0.504010] pci 0000:05:00.0: CardBus bridge to [bus 06-09]
[    0.509594] pci 0000:05:00.0:   bridge window [io  0x2000-0x20ff]
[    0.515706] pci 0000:05:00.0:   bridge window [io  0x2400-0x24ff]
[    0.521816] pci 0000:05:00.0:   bridge window [mem 0x44000000-0x47ffffff pref]
[    0.529054] pci 0000:05:00.0:   bridge window [mem 0x48000000-0x4bffffff]
[    0.535855] pci 0000:00:1e.0: PCI bridge to [bus 05-06]
[    0.541095] pci 0000:00:1e.0:   bridge window [io  0x2000-0x3fff]
[    0.547208] pci 0000:00:1e.0:   bridge window [mem 0xe0000000-0xe20fffff]
[    0.554017] pci 0000:00:1e.0:   bridge window [mem 0xe2100000-0xe40fffff 64bit pref]
[    0.561779] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.561783] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.561787] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.561791] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[    0.561795] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[    0.561799] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[    0.561803] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
[    0.561807] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
[    0.561811] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
[    0.561815] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
[    0.561819] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
[    0.561823] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff]
[    0.561828] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff]
[    0.561832] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff]
[    0.561836] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff]
[    0.561840] pci_bus 0000:00: resource 19 [mem 0x000f0000-0x000fffff]
[    0.561844] pci_bus 0000:00: resource 20 [mem 0x40000000-0xfebfffff]
[    0.561848] pci_bus 0000:00: resource 21 [mem 0xfed40000-0xfed44fff]
[    0.561852] pci_bus 0000:01: resource 0 [io  0x4000-0x4fff]
[    0.561856] pci_bus 0000:01: resource 1 [mem 0xe4100000-0xe41fffff]
[    0.561860] pci_bus 0000:01: resource 2 [mem 0x40000000-0x401fffff 64bit pref]
[    0.561864] pci_bus 0000:02: resource 1 [mem 0xe4200000-0xe42fffff]
[    0.561869] pci_bus 0000:05: resource 0 [io  0x2000-0x3fff]
[    0.561873] pci_bus 0000:05: resource 1 [mem 0xe0000000-0xe20fffff]
[    0.561877] pci_bus 0000:05: resource 2 [mem 0xe2100000-0xe40fffff 64bit pref]
[    0.561881] pci_bus 0000:05: resource 4 [io  0x0000-0x0cf7]
[    0.561885] pci_bus 0000:05: resource 5 [io  0x0d00-0xffff]
[    0.561889] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
[    0.561893] pci_bus 0000:05: resource 7 [mem 0x000c0000-0x000c3fff]
[    0.561897] pci_bus 0000:05: resource 8 [mem 0x000c4000-0x000c7fff]
[    0.561901] pci_bus 0000:05: resource 9 [mem 0x000c8000-0x000cbfff]
[    0.561905] pci_bus 0000:05: resource 10 [mem 0x000cc000-0x000cffff]
[    0.561909] pci_bus 0000:05: resource 11 [mem 0x000d0000-0x000d3fff]
[    0.561913] pci_bus 0000:05: resource 12 [mem 0x000d4000-0x000d7fff]
[    0.561918] pci_bus 0000:05: resource 13 [mem 0x000d8000-0x000dbfff]
[    0.561922] pci_bus 0000:05: resource 14 [mem 0x000dc000-0x000dffff]
[    0.561926] pci_bus 0000:05: resource 15 [mem 0x000e0000-0x000e3fff]
[    0.561930] pci_bus 0000:05: resource 16 [mem 0x000e4000-0x000e7fff]
[    0.561934] pci_bus 0000:05: resource 17 [mem 0x000e8000-0x000ebfff]
[    0.561938] pci_bus 0000:05: resource 18 [mem 0x000ec000-0x000effff]
[    0.561942] pci_bus 0000:05: resource 19 [mem 0x000f0000-0x000fffff]
[    0.561946] pci_bus 0000:05: resource 20 [mem 0x40000000-0xfebfffff]
[    0.561950] pci_bus 0000:05: resource 21 [mem 0xfed40000-0xfed44fff]
[    0.561954] pci_bus 0000:06: resource 0 [io  0x2000-0x20ff]
[    0.561958] pci_bus 0000:06: resource 1 [io  0x2400-0x24ff]
[    0.561962] pci_bus 0000:06: resource 2 [mem 0x44000000-0x47ffffff pref]
[    0.561966] pci_bus 0000:06: resource 3 [mem 0x48000000-0x4bffffff]
[    0.562022] NET: Registered protocol family 2
[    0.566601] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.573694] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.580192] TCP: Hash tables configured (established 8192 bind 8192)
[    0.586594] TCP: reno registered
[    0.589842] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.595789] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.602238] NET: Registered protocol family 1
[    0.606629] pci 0000:00:02.0: Boot video device
[    0.607936] PCI: CLS 64 bytes, default 64
[    0.608027] Unpacking initramfs...
[    0.960428] Freeing initrd memory: 10316K (f6bca000 - f75dd000)
[    0.967092] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.973253] audit: initializing netlink subsys (disabled)
[    0.978695] audit: type=2000 audit(1402242441.977:1): initialized
[    0.985246] bounce pool size: 64 pages
[    0.989018] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.998899] VFS: Disk quotas dquot_6.5.2
[    1.002925] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.010292] msgmni has been set to 1741
[    1.014653] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.022063] io scheduler noop registered
[    1.026013] io scheduler deadline registered
[    1.030413] io scheduler cfq registered (default)
[    1.035472] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[    1.035773] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[    1.036052] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
[    1.036319] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X
[    1.036505] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[    1.043484] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    1.050027] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[    1.050059] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
[    1.057036] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[    1.063580] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
[    1.063615] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
[    1.070592] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
[    1.070624] pcieport 0000:00:1c.3: Signaling PME through PCIe PME interrupt
[    1.077603] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme loaded
[    1.077662] intel_idle: does not run on family 6 model 14
[    1.077789] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:24/PNP0C09:00/PNP0C0E:00/input/input0
[    1.088767] ACPI: Sleep Button [SLPB]
[    1.092535] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:24/PNP0C09:00/PNP0C0D:00/input/input1
[    1.103477] ACPI: Lid Switch [LID]
[    1.107012] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    1.114425] ACPI: Power Button [PWRF]
[    1.118384] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    1.125448] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input3
[    1.134531] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.161671] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.170095] Linux agpgart interface v0.103
[    1.174258] agpgart-intel 0000:00:00.0: Intel 945GM Chipset
[    1.179887] agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
[    1.189213] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
[    1.195747] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    1.202616] [drm] Initialized drm 1.1.0 20060810
[    1.207803] [drm:i915_dump_device_info], i915 device info: gen=3, pciid=0x27a2 flags=is_mobile,is_i945gm,has_fbc,has_hotplug,cursor_needs_physical,has_overlay,overlay_needs_physical,supports_tv,
[    1.207860] [drm:intel_detect_pch], No PCH found.
[    1.207864] [drm] Memory usable by graphics device = 256M
[    1.213283] [drm:i915_gem_gtt_init], GMADR size = 256M
[    1.213286] [drm:i915_gem_gtt_init], GTT stolen size = 8M
[    1.213551] [drm:intel_opregion_setup], graphic opregion physical addr: 0x0
[    1.213555] [drm:intel_opregion_setup], ACPI OpRegion not supported!
[    1.213582] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.220210] [drm] Driver supports precise vblank timestamp query.
[    1.226321] [drm:init_vbt_defaults], Set default to SSC at 100000 kHz
[    1.226327] i915 0000:00:02.0: Invalid ROM contents
[    1.231214] [drm:intel_parse_bios], VBT signature missing
[    1.231217] [drm] failed to find VBIOS tables
[    1.235593] [drm:intel_dsm_pci_probe], no _DSM method for intel device
[    1.235603] [drm:i915_gem_init_stolen], found 8388608 bytes of stolen memory at 3f800000
[    1.235640] [drm] GPU crash dump saved to /sys/class/drm/card0/error
[    1.236583] [drm] GPU hangs can indicate a bug anywhere in the entire gfx stack, including userspace.
[    1.236583] [drm] Please file a _new_ bug report on bugs.freedesktop.org against DRI -> DRM/Intel
[    1.236583] [drm] drm/i915 developers can then reassign to the right component if it's not a kernel issue.
[    1.236583] [drm] The gpu crash dump is required to analyze gpu hangs, so please always attach it.
[    1.236583] i915: render error detected, EIR: 0x00000010
[    1.236583] i915: page table error
[    1.236583] i915:   PGTBL_ER: 0x00000013
[    1.236583] [drm:i915_report_and_clear_eir] *ERROR* EIR stuck: 0x00000010, masking
[    1.236583] i915: render error detected, EIR: 0x00000010
[    1.236583] i915: page table error
[    1.236583] i915:   PGTBL_ER: 0x00000013
[    1.311612] [drm:intel_modeset_init], 2 display pipes available.
[    1.311620] [drm:intel_crtc_init], swapping pipes & planes for FBC
[    1.311624] [drm:intel_modeset_init], pipe A sprite A init failed: -19
[    1.311629] [drm:intel_crtc_init], swapping pipes & planes for FBC
[    1.311632] [drm:intel_modeset_init], pipe B sprite B init failed: -19
[    1.311639] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    1.372014] [drm] GMBUS [i915 gmbus panel] timed out, falling back to bit banging on pin 3
[    1.409117] [drm:intel_lvds_init], using preferred mode from EDID: 
[    1.409123] [drm:drm_mode_debug_printmodeline], Modeline 8:"1024x768" 50 54160 1024 1048 1184 1344 768 771 777 806 0x48 0xa
[    1.409129] [drm:intel_lvds_init], detected single-link lvds configuration
[    1.409175] [drm:intel_panel_setup_backlight], failed to setup backlight for connector LVDS-1
[    1.409286] [drm:i915_gem_setup_global_gtt], clearing unused GTT space: [0, ffff000]
[    1.411683] [drm:i915_gem_object_create_stolen], creating stolen object: size=20000
[    1.411688] [drm:i915_pages_create_for_stolen], offset=0x0, size=131072
[    1.411814] [drm] initialized overlay support
[    1.416185] [drm:intel_modeset_readout_hw_state], [CRTC:3] hw state readout: disabled
[    1.416194] [drm:intel_modeset_readout_hw_state], [CRTC:4] hw state readout: enabled
[    1.416199] [drm:intel_modeset_readout_hw_state], [ENCODER:6:LVDS-6] hw state readout: enabled, pipe B
[    1.416204] [drm:intel_modeset_readout_hw_state], [ENCODER:17:DAC-17] hw state readout: disabled, pipe A
[    1.416209] [drm:intel_modeset_readout_hw_state], [ENCODER:19:TV-19] hw state readout: disabled, pipe A
[    1.416213] [drm:intel_modeset_readout_hw_state], [CONNECTOR:5:LVDS-1] hw state readout: enabled
[    1.416217] [drm:intel_modeset_readout_hw_state], [CONNECTOR:16:VGA-1] hw state readout: disabled
[    1.416221] [drm:intel_modeset_readout_hw_state], [CONNECTOR:18:SVIDEO-1] hw state readout: disabled
[    1.416227] [drm:intel_dump_pipe_config], [CRTC:3][setup_hw_state] config for pipe A
[    1.416230] [drm:intel_dump_pipe_config], cpu_transcoder: A
[    1.416233] [drm:intel_dump_pipe_config], pipe bpp: 0, dithering: 0
[    1.416237] [drm:intel_dump_pipe_config], fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[    1.416241] [drm:intel_dump_pipe_config], dp: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[    1.416244] [drm:intel_dump_pipe_config], requested mode:
[    1.416249] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0
[    1.416252] [drm:intel_dump_pipe_config], adjusted mode:
[    1.416257] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0
[    1.416261] [drm:intel_dump_crtc_timings], crtc timings: 0 0 0 0 0 0 0 0 0, type: 0x0 flags: 0x0
[    1.416264] [drm:intel_dump_pipe_config], port clock: 0
[    1.416267] [drm:intel_dump_pipe_config], pipe src size: 0x0
[    1.416271] [drm:intel_dump_pipe_config], gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000
[    1.416274] [drm:intel_dump_pipe_config], pch pfit: pos: 0x00000000, size: 0x00000000, disabled
[    1.416277] [drm:intel_dump_pipe_config], ips: 0
[    1.416280] [drm:intel_dump_pipe_config], double wide: 0
[    1.416284] [drm:intel_dump_pipe_config], [CRTC:4][setup_hw_state] config for pipe B
[    1.416287] [drm:intel_dump_pipe_config], cpu_transcoder: B
[    1.416290] [drm:intel_dump_pipe_config], pipe bpp: 0, dithering: 0
[    1.416294] [drm:intel_dump_pipe_config], fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[    1.416298] [drm:intel_dump_pipe_config], dp: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[    1.416301] [drm:intel_dump_pipe_config], requested mode:
[    1.416306] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 1024 0 0 0 768 0 0 0 0x0 0x0
[    1.416309] [drm:intel_dump_pipe_config], adjusted mode:
[    1.416314] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0xa
[    1.416319] [drm:intel_dump_crtc_timings], crtc timings: 54167 1024 1048 1184 1344 768 771 777 806, type: 0x0 flags: 0xa
[    1.416322] [drm:intel_dump_pipe_config], port clock: 54167
[    1.416325] [drm:intel_dump_pipe_config], pipe src size: 1024x768
[    1.416329] [drm:intel_dump_pipe_config], gmch pfit: control: 0x00000008, ratios: 0x00000000, lvds border: 0x00000000
[    1.416332] [drm:intel_dump_pipe_config], pch pfit: pos: 0x00000000, size: 0x00000000, disabled
[    1.416335] [drm:intel_dump_pipe_config], ips: 0
[    1.416338] [drm:intel_dump_pipe_config], double wide: 0
[    1.416342] [drm:intel_connector_check_state], [CONNECTOR:5:LVDS-1]
[    1.416347] [drm:check_encoder_state], [ENCODER:6:LVDS-6]
[    1.416350] [drm:check_encoder_state], [ENCODER:17:DAC-17]
[    1.416354] [drm:check_encoder_state], [ENCODER:19:TV-19]
[    1.416358] [drm:check_crtc_state], [CRTC:3]
[    1.416361] [drm:check_crtc_state], [CRTC:4]
[    1.416378] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:5:LVDS-1]
[    1.416381] [drm:intel_lvds_detect], [CONNECTOR:5:LVDS-1]
[    1.416396] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:5:LVDS-1] probed modes :
[    1.416403] [drm:drm_mode_debug_printmodeline], Modeline 8:"1024x768" 50 54160 1024 1048 1184 1344 768 771 777 806 0x48 0xa
[    1.416408] [drm:drm_mode_debug_printmodeline], Modeline 12:"1024x768" 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[    1.416414] [drm:drm_mode_debug_printmodeline], Modeline 9:"1024x768" 40 43330 1024 1048 1184 1344 768 771 777 806 0x40 0xa
[    1.416420] [drm:drm_mode_debug_printmodeline], Modeline 10:"800x600" 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
[    1.416425] [drm:drm_mode_debug_printmodeline], Modeline 11:"640x480" 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
[    1.416429] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:16:VGA-1]
[    1.416433] [drm:intel_crt_detect], [CONNECTOR:16:VGA-1] force=1
[    1.428017] [drm:intel_crt_detect], CRT not detected via hotplug
[    1.479013] [drm] GMBUS [i915 gmbus vga] timed out, falling back to bit banging on pin 2
[    1.487390] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga
[    1.487393] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found]
[    1.487397] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:16:VGA-1] disconnected
[    1.487401] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:18:SVIDEO-1]
[    1.487405] [drm:intel_tv_detect], [CONNECTOR:18:SVIDEO-1] force=1
[    1.487410] [drm:intel_get_load_detect_pipe], [CONNECTOR:18:SVIDEO-1], [ENCODER:19:TV-19]
[    1.487413] [drm:intel_get_load_detect_pipe], creating tmp fb for load-detection
[    1.487424] [drm:intel_modeset_affected_pipes], set mode pipe masks: modeset: 1, prepare: 1, disable: 0
[    1.487429] [drm:connected_sink_compute_bpp], [CONNECTOR:18:SVIDEO-1] checking for sink bpp constrains
[    1.487433] [drm:intel_tv_compute_config], forcing bpc to 8 for TV
[    1.487437] [drm:intel_modeset_pipe_config], plane bpp: 24, pipe bpp: 24, dithering: 0
[    1.487440] [drm:intel_dump_pipe_config], [CRTC:3][modeset] config for pipe A
[    1.487443] [drm:intel_dump_pipe_config], cpu_transcoder: A
[    1.487446] [drm:intel_dump_pipe_config], pipe bpp: 24, dithering: 0
[    1.487450] [drm:intel_dump_pipe_config], fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[    1.487454] [drm:intel_dump_pipe_config], dp: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[    1.487457] [drm:intel_dump_pipe_config], requested mode:
[    1.487463] [drm:drm_mode_debug_printmodeline], Modeline 0:"NTSC 480i" 0 107520 1280 1368 1496 1712 1024 1027 1034 1104 0x40 0x0
[    1.487466] [drm:intel_dump_pipe_config], adjusted mode:
[    1.487471] [drm:drm_mode_debug_printmodeline], Modeline 0:"NTSC 480i" 0 107520 1280 1368 1496 1712 1024 1027 1034 1104 0x40 0x0
[    1.487476] [drm:intel_dump_crtc_timings], crtc timings: 108000 1280 1368 1496 1712 1024 1027 1034 1104, type: 0x40 flags: 0x0
[    1.487479] [drm:intel_dump_pipe_config], port clock: 108000
[    1.487482] [drm:intel_dump_pipe_config], pipe src size: 1280x1024
[    1.487486] [drm:intel_dump_pipe_config], gmch pfit: control: 0x00000000, ratios: 0x00000000, lvds border: 0x00000000
[    1.487490] [drm:intel_dump_pipe_config], pch pfit: pos: 0x00000000, size: 0x00000000, disabled
[    1.487492] [drm:intel_dump_pipe_config], ips: 0
[    1.487495] [drm:intel_dump_pipe_config], double wide: 0
[    1.494848] [drm:i9xx_update_plane], Writing base 00020000 00000000 0 0 5120
[    1.494855] [drm:intel_update_fbc], no output, disabling
[    1.494862] [drm:intel_crtc_mode_set], [ENCODER:19:TV-19] set [MODE:0:NTSC 480i]
[    1.500628] [drm:i9xx_get_fifo_size], FIFO size - (0x00001d9c) A: 28
[    1.500632] [drm:i9xx_get_fifo_size], FIFO size - (0x00001d9c) B: 31
[    1.500635] [drm:intel_calculate_wm], FIFO entries required for mode: 34
[    1.500638] [drm:intel_calculate_wm], FIFO watermark level: -5
[    1.500641] [drm:i9xx_update_wm], FIFO watermarks - A: 26, B: 1
[    1.500644] [drm:i9xx_update_wm], self-refresh entries: 80
[    1.500648] [drm:i9xx_update_wm], Setting FIFO watermarks - A: 26, B: 1, C: 2, SR 47
[    1.500651] [drm:i9xx_update_wm], memory self refresh enabled
[    1.532018] [drm:intel_update_fbc], disabled per chip default
[    1.532026] [drm:intel_connector_check_state], [CONNECTOR:5:LVDS-1]
[    1.532031] [drm:intel_connector_check_state], [CONNECTOR:18:SVIDEO-1]
[    1.532035] [drm:check_encoder_state], [ENCODER:6:LVDS-6]
[    1.532039] [drm:check_encoder_state], [ENCODER:17:DAC-17]
[    1.532043] [drm:check_encoder_state], [ENCODER:19:TV-19]
[    1.532046] [drm:check_crtc_state], [CRTC:3]
[    1.532057] [drm:check_crtc_state], [CRTC:4]
[    1.566017] [drm:intel_tv_detect_type], TV detected: c0007, 7f0000aa
[    1.566020] [drm:intel_tv_detect_type], Unrecognised TV connection
[    1.598018] [drm:intel_release_load_detect_pipe], [CONNECTOR:18:SVIDEO-1], [ENCODER:19:TV-19]
[    1.598023] [drm:intel_modeset_affected_pipes], set mode pipe masks: modeset: 0, prepare: 0, disable: 1
[    1.640020] [drm:i9xx_get_fifo_size], FIFO size - (0x00001d9c) A: 28
[    1.640024] [drm:i9xx_get_fifo_size], FIFO size - (0x00001d9c) B: 31
[    1.640027] [drm:i9xx_update_wm], FIFO watermarks - A: 26, B: 29
[    1.640030] [drm:i9xx_update_wm], Setting FIFO watermarks - A: 26, B: 29, C: 2, SR 1
[    1.640034] [drm:i9xx_update_wm], memory self refresh disabled
[    1.640036] [drm:intel_update_fbc], no output, disabling
[    1.640043] [drm:intel_connector_check_state], [CONNECTOR:5:LVDS-1]
[    1.640048] [drm:check_encoder_state], [ENCODER:6:LVDS-6]
[    1.640051] [drm:check_encoder_state], [ENCODER:17:DAC-17]
[    1.640055] [drm:check_encoder_state], [ENCODER:19:TV-19]
[    1.640058] [drm:check_crtc_state], [CRTC:3]
[    1.640062] [drm:check_crtc_state], [CRTC:4]
[    1.640243] [drm:drm_helper_probe_single_connector_modes], [CONNECTOR:18:SVIDEO-1] disconnected
[    1.640248] [drm:drm_setup_crtcs], 
[    1.640252] [drm:drm_enable_connectors], connector 5 enabled? yes
[    1.640255] [drm:drm_enable_connectors], connector 16 enabled? no
[    1.640258] [drm:drm_enable_connectors], connector 18 enabled? no
[    1.640261] [drm:drm_target_preferred], looking for cmdline mode on connector 5
[    1.640265] [drm:drm_target_preferred], looking for preferred mode on connector 5
[    1.640268] [drm:drm_target_preferred], found mode 1024x768
[    1.640271] [drm:drm_setup_crtcs], picking CRTCs for 4096x4096 config
[    1.640275] [drm:drm_setup_crtcs], desired mode 1024x768 set on crtc 4
[    1.640280] [drm:intelfb_create], no BIOS fb, allocating a new one
[    1.640284] [drm:i915_gem_object_create_stolen], creating stolen object: size=300000
[    1.640289] [drm:i915_pages_create_for_stolen], offset=0x20000, size=3145728
[    1.642643] [drm:intelfb_create], allocated 1024x768 fb: 0x00020000, bo f4a9e900
[    1.642759] fbcon: inteldrmfb (fb0) is primary device
[    1.642811] [drm:intel_crtc_set_config], [CRTC:3] [NOFB]
[    1.642814] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=0
[    1.642817] [drm:intel_modeset_stage_output_state], [CONNECTOR:5:LVDS-1] to [CRTC:4]
[    1.642820] [drm:intel_crtc_set_config], [CRTC:4] [FB:34] #connectors=1 (x y) (0 0)
[    1.642822] [drm:intel_set_config_compute_mode_changes], inactive crtc, full mode set
[    1.642823] [drm:intel_set_config_compute_mode_changes], modes are different, full mode set
[    1.642827] [drm:drm_mode_debug_printmodeline], Modeline 0:"" 0 0 0 0 0 0 0 0 0 0 0x0 0x0
[    1.642831] [drm:drm_mode_debug_printmodeline], Modeline 33:"1024x768" 50 54160 1024 1048 1184 1344 768 771 777 806 0x48 0xa
[    1.642833] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:4], mode_changed=1, fb_changed=0
[    1.642836] [drm:intel_modeset_stage_output_state], [CONNECTOR:5:LVDS-1] to [CRTC:4]
[    1.642840] [drm:intel_modeset_affected_pipes], set mode pipe masks: modeset: 2, prepare: 2, disable: 0
[    1.642843] [drm:connected_sink_compute_bpp], [CONNECTOR:5:LVDS-1] checking for sink bpp constrains
[    1.642846] [drm:intel_lvds_compute_config], forcing display bpp (was 24) to LVDS (18)
[    1.642850] [drm:intel_modeset_pipe_config], plane bpp: 24, pipe bpp: 18, dithering: 1
[    1.642852] [drm:intel_dump_pipe_config], [CRTC:4][modeset] config for pipe B
[    1.642853] [drm:intel_dump_pipe_config], cpu_transcoder: B
[    1.642855] [drm:intel_dump_pipe_config], pipe bpp: 18, dithering: 1
[    1.642858] [drm:intel_dump_pipe_config], fdi/pch: 0, lanes: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[    1.642860] [drm:intel_dump_pipe_config], dp: 0, gmch_m: 0, gmch_n: 0, link_m: 0, link_n: 0, tu: 0
[    1.642861] [drm:intel_dump_pipe_config], requested mode:
[    1.642865] [drm:drm_mode_debug_printmodeline], Modeline 0:"1024x768" 50 54160 1024 1048 1184 1344 768 771 777 806 0x48 0xa
[    1.642866] [drm:intel_dump_pipe_config], adjusted mode:
[    1.642870] [drm:drm_mode_debug_printmodeline], Modeline 0:"1024x768" 50 54160 1024 1048 1184 1344 768 771 777 806 0x48 0xa
[    1.642874] [drm:intel_dump_crtc_timings], crtc timings: 54160 1024 1048 1184 1344 768 771 777 806, type: 0x48 flags: 0xa
[    1.642875] [drm:intel_dump_pipe_config], port clock: 54160
[    1.642877] [drm:intel_dump_pipe_config], pipe src size: 1024x768
[    1.642879] [drm:intel_dump_pipe_config], gmch pfit: control: 0x00000008, ratios: 0x00000000, lvds border: 0x00000000
[    1.642881] [drm:intel_dump_pipe_config], pch pfit: pos: 0x00000000, size: 0x00000000, disabled
[    1.642882] [drm:intel_dump_pipe_config], ips: 0
[    1.642884] [drm:intel_dump_pipe_config], double wide: 0
[    1.926019] [drm:i9xx_pfit_disable], disabling pfit, current: 0x00000008
[    1.926022] [drm:i9xx_get_fifo_size], FIFO size - (0x00001d9c) A: 28
[    1.926025] [drm:i9xx_get_fifo_size], FIFO size - (0x00001d9c) B: 31
[    1.926026] [drm:i9xx_update_wm], FIFO watermarks - A: 26, B: 29
[    1.926029] [drm:i9xx_update_wm], Setting FIFO watermarks - A: 26, B: 29, C: 2, SR 1
[    1.926030] [drm:i9xx_update_wm], memory self refresh disabled
[    1.926035] [drm:i9xx_get_refclk], using SSC reference clock of 100000 kHz
[    1.926244] [drm:i9xx_update_plane], Writing base 00020000 00000000 0 0 4096
[    1.926248] [drm:intel_crtc_mode_set], [ENCODER:6:LVDS-6] set [MODE:0:1024x768]
[    1.926890] [drm:i9xx_get_fifo_size], FIFO size - (0x00001d9c) A: 28
[    1.926892] [drm:intel_calculate_wm], FIFO entries required for mode: 17
[    1.926893] [drm:intel_calculate_wm], FIFO watermark level: 9
[    1.926895] [drm:i9xx_get_fifo_size], FIFO size - (0x00001d9c) B: 31
[    1.926897] [drm:i9xx_update_wm], FIFO watermarks - A: 9, B: 29
[    1.926898] [drm:i9xx_update_wm], self-refresh entries: 64
[    1.926900] [drm:i9xx_update_wm], Setting FIFO watermarks - A: 9, B: 29, C: 2, SR 63
[    1.926902] [drm:i9xx_update_wm], memory self refresh enabled
[    1.948017] [drm:intel_update_fbc], disabled per chip default
[    1.967018] tsc: Refined TSC clocksource calibration: 1662.499 MHz
[    2.230018] [drm:intel_connector_check_state], [CONNECTOR:5:LVDS-1]
[    2.230022] [drm:check_encoder_state], [ENCODER:6:LVDS-6]
[    2.230024] [drm:check_encoder_state], [ENCODER:17:DAC-17]
[    2.230026] [drm:check_encoder_state], [ENCODER:19:TV-19]
[    2.230028] [drm:check_crtc_state], [CRTC:3]
[    2.230030] [drm:check_crtc_state], [CRTC:4]
[    2.230060] [drm:intel_crtc_set_config], [CRTC:4] [FB:34] #connectors=1 (x y) (0 0)
[    2.230062] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:4], mode_changed=0, fb_changed=0
[    2.230065] [drm:intel_modeset_stage_output_state], [CONNECTOR:5:LVDS-1] to [CRTC:4]
[    2.235446] Console: switching to colour frame buffer device 128x48
[    2.235452] [drm:intel_crtc_set_config], [CRTC:4] [FB:34] #connectors=1 (x y) (0 0)
[    2.235454] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:4], mode_changed=0, fb_changed=0
[    2.235457] [drm:intel_modeset_stage_output_state], [CONNECTOR:5:LVDS-1] to [CRTC:4]
[    2.258219] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[    2.264472] i915 0000:00:02.0: registered panic notifier
[    2.269862] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    2.277274] ahci 0000:00:1f.2: version 3.0
[    2.277483] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
[    2.277524] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    2.284250] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode
[    2.292612] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part 
[    2.301467] scsi0 : ahci
[    2.304238] scsi1 : ahci
[    2.306982] scsi2 : ahci
[    2.309730] scsi3 : ahci
[    2.312395] ata1: SATA max UDMA/133 abar m1024@0xe4444400 port 0xe4444500 irq 44
[    2.319881] ata2: DUMMY
[    2.322367] ata3: DUMMY
[    2.324852] ata4: DUMMY
[    2.327470] ata_piix 0000:00:1f.1: version 2.13
[    2.328241] scsi4 : ata_piix
[    2.331345] scsi5 : ata_piix
[    2.336478] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x5080 irq 14
[    2.345679] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x5088 irq 15
[    2.354929] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    2.365364] ata6: port disabled--ignoring
[    2.377376] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.384557] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.391895] mousedev: PS/2 mouse device common for all mice
[    2.399632] rtc_cmos 00:06: RTC can wake from S4
[    2.406519] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    2.414696] rtc_cmos 00:06: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    2.424562] device-mapper: uevent: version 1.0.3
[    2.431376] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    2.442149] TCP: cubic registered
[    2.447821] NET: Registered protocol family 10
[    2.454713] mip6: Mobile IPv6
[    2.459783] NET: Registered protocol family 17
[    2.466394] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    2.477194] Key type dns_resolver registered
[    2.483857] Using IPI No-Shortcut mode
[    2.489845] registered taskstats version 1
[    2.496551] regulator-dummy: disabling
[    2.502463] rtc_cmos 00:06: setting system clock to 2014-06-08 15:47:25 UTC (1402242445)
[    2.508720] ata5.00: ATAPI: DVD/CDRW UJDA775, CB03, max UDMA/33
[    2.514624] ata5.00: configured for UDMA/33
[    2.789040] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.797537] ata1.00: ATA-7: INTEL SSDSA2M040G2GC, 2CV102M3, max UDMA/133
[    2.806299] ata1.00: 78165360 sectors, multi 1: LBA48 NCQ (depth 31/32)
[    2.815243] ata1.00: configured for UDMA/133
[    2.821719] scsi 0:0:0:0: Direct-Access     ATA      INTEL SSDSA2M040 2CV1 PQ: 0 ANSI: 5
[    2.832137] sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    2.841975] sd 0:0:0:0: [sda] Write Protect is off
[    2.848859] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.848875] scsi 4:0:0:0: CD-ROM            MATSHITA DVD/CDRW UJDA775 CB03 PQ: 0 ANSI: 5
[    2.848896] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.849685]  sda: sda1 sda2
[    2.850139] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.893219] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    2.902209] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.909946] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    2.910667] Freeing unused kernel memory: 480K (c15de000 - c1656000)
[    2.919329] Write protecting the kernel text: 4116k
[    2.926483] Write protecting the kernel read-only data: 1564k
[    2.955686] udevd[85]: starting version 175
[    2.964521] [drm:intel_crtc_set_config], [CRTC:4] [FB:34] #connectors=1 (x y) (0 0)
[    2.964527] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:4], mode_changed=0, fb_changed=0
[    2.964531] [drm:intel_modeset_stage_output_state], [CONNECTOR:5:LVDS-1] to [CRTC:4]
[    2.970089] Switched to clocksource tsc
[    3.040167] thermal LNXTHERM:00: registered as thermal_zone0
[    3.054305] pps_core: LinuxPPS API ver. 1 registered
[    3.059434] ACPI: Thermal Zone [THM0] (59 C)
[    3.076937] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    3.077397] thermal LNXTHERM:01: registered as thermal_zone1
[    3.077399] ACPI: Thermal Zone [THM1] (50 C)
[    3.109615] PTP clock support registered
[    3.126191] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    3.136802] ACPI: bus type USB registered
[    3.144873] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    3.152637] usbcore: registered new interface driver usbfs
[    3.152658] usbcore: registered new interface driver hub
[    3.155174] usbcore: registered new device driver usb
[    3.155622] uhci_hcd: USB Universal Host Controller Interface driver
[    3.155848] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    3.155857] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    3.155904] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00005000
[    3.155997] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    3.155999] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.156009] usb usb1: Product: UHCI Host Controller
[    3.156011] usb usb1: Manufacturer: Linux 3.14.4-gnuowen uhci_hcd
[    3.156013] usb usb1: SerialNumber: 0000:00:1d.0
[    3.192450] hub 1-0:1.0: USB hub found
[    3.192462] hub 1-0:1.0: 2 ports detected
[    3.192802] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    3.192815] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    3.192869] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00005020
[    3.192944] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    3.192946] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.192949] usb usb2: Product: UHCI Host Controller
[    3.192951] usb usb2: Manufacturer: Linux 3.14.4-gnuowen uhci_hcd
[    3.192953] usb usb2: SerialNumber: 0000:00:1d.1
[    3.193142] hub 2-0:1.0: USB hub found
[    3.193152] hub 2-0:1.0: 2 ports detected
[    3.193426] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    3.193434] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    3.193479] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00005040
[    3.193549] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    3.193552] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.193554] usb usb3: Product: UHCI Host Controller
[    3.193556] usb usb3: Manufacturer: Linux 3.14.4-gnuowen uhci_hcd
[    3.193559] usb usb3: SerialNumber: 0000:00:1d.2
[    3.193739] hub 3-0:1.0: USB hub found
[    3.193749] hub 3-0:1.0: 2 ports detected
[    3.194040] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    3.194047] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    3.194109] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00005060
[    3.194186] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    3.194189] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.194191] usb usb4: Product: UHCI Host Controller
[    3.194193] usb usb4: Manufacturer: Linux 3.14.4-gnuowen uhci_hcd
[    3.194196] usb usb4: SerialNumber: 0000:00:1d.3
[    3.194371] hub 4-0:1.0: USB hub found
[    3.194382] hub 4-0:1.0: 2 ports detected
[    3.205982] sdhci: Secure Digital Host Controller Interface driver
[    3.205983] sdhci: Copyright(c) Pierre Ossman
[    3.206508] sdhci-pci 0000:05:00.2: SDHCI controller found [1180:0822] (rev 18)
[    3.206526] pci 0000:00:1e.0: enabling device (0004 -> 0007)
[    3.207684] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[    3.207695] mmc0: no vqmmc regulator found
[    3.207696] mmc0: no vmmc regulator found
[    3.208705] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[    3.208932] mmc0: SDHCI controller on PCI [0000:05:00.2] using DMA
[    3.579327] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[    3.591064] e1000e 0000:01:00.0: irq 45 for MSI/MSI-X
[    3.591071] [drm:intel_crtc_set_config], [CRTC:4] [FB:34] #connectors=1 (x y) (0 0)
[    3.591076] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:4], mode_changed=0, fb_changed=0
[    3.591080] [drm:intel_modeset_stage_output_state], [CONNECTOR:5:LVDS-1] to [CRTC:4]
[    3.607697] xor: measuring software checksum speed
[    3.622007]    pIII_sse  :  4296.000 MB/sec
[    3.630068] firewire_ohci 0000:05:00.1: added OHCI v1.10 device as card 0, 4 IR + 4 IT contexts, quirks 0x11
[    3.636005]    prefetch64-sse:  4652.000 MB/sec
[    3.636007] xor: using function: prefetch64-sse (4652.000 MB/sec)
[    3.653047] raid6: mmxx1     1613 MB/s
[    3.673030] raid6: mmxx2     1683 MB/s
[    3.693037] raid6: sse1x1    1210 MB/s
[    3.704513] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:16:d3:36:ef:cc
[    3.712525] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection
[    3.713043] raid6: sse1x2    1589 MB/s
[    3.723351] e1000e 0000:01:00.0 eth0: MAC: 2, PHY: 2, PBA No: 005302-003
[    3.730028] raid6: sse2x1    1878 MB/s
[    3.747034] raid6: sse2x2    2011 MB/s
[    3.750830] raid6: using algorithm sse2x2 (2011 MB/s)
[    3.755935] raid6: using intx1 recovery algorithm
[    3.766026] bio: create slab <bio-1> at 1
[    3.770521] Btrfs loaded
[    3.773132] BTRFS: selftest: Running btrfs free space cache tests
[    3.779297] BTRFS: selftest: Running extent only tests
[    3.784505] BTRFS: selftest: Running bitmap only tests
[    3.789710] BTRFS: selftest: Running bitmap and extent tests
[    3.795454] BTRFS: selftest: Free space cache tests finished
[    3.795470] usb 3-2: new full-speed USB device number 2 using uhci_hcd
[    3.807788] BTRFS: selftest: Running extent buffer operation tests
[    3.813870] BTRFS: selftest: Running btrfs_split_item tests
[    3.819724] BTRFS: selftest: Running find delalloc tests
[    3.935536] usb 3-2: New USB device found, idVendor=17ef, idProduct=1000
[    3.942338] usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.955020] hub 3-2:1.0: USB hub found
[    3.960523] hub 3-2:1.0: 4 ports detected
[    3.972058] BTRFS: selftest: Running btrfs_get_extent tests
[    3.977816] BTRFS: selftest: Running hole first btrfs_get_extent test
[    4.073029] usb 4-1: new full-speed USB device number 2 using uhci_hcd
[    4.097461] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    4.154138] firewire_core 0000:05:00.1: created device fw0: GUID 0000000000000000, S400
[    4.211574] random: init urandom read with 109 bits of entropy available
[    4.233170] usb 4-1: New USB device found, idVendor=0a5c, idProduct=2110
[    4.239960] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.247219] usb 4-1: Product: BCM2045B
[    4.251041] usb 4-1: Manufacturer: Broadcom Corp
[    4.313789] random: nonblocking pool is initialized
[    4.363039] usb 4-2: new full-speed USB device number 3 using uhci_hcd
[    4.484548] Adding 3906556k swap on /dev/sda2.  Priority:-1 extents:1 across:3906556k SS
[    4.529837] udevd[404]: starting version 175
[    4.537173] usb 4-2: New USB device found, idVendor=0483, idProduct=2016
[    4.537180] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.537184] usb 4-2: Product: Biometric Coprocessor
[    4.537188] usb 4-2: Manufacturer: STMicroelectronics
[    4.582595] lp: driver loaded but no devices found
[    4.657777] ACPI: processor limited to max C-state 2
[    4.658326] Monitor-Mwait will be used to enter C-1 state
[    4.664486] ACPI: AC Adapter [AC] (on-line)
[    4.664524] ACPI Exception: AE_NOT_FOUND, Error reading AC Adapter state (20131218/ac-77)
[    4.671030] tsc: Marking TSC unstable due to TSC halts in idle
[    4.671053] ACPI: acpi_idle registered with cpuidle
[    4.672785] Switched to clocksource hpet
[    4.723418] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.723424] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[    4.725261] ehci-pci: EHCI PCI platform driver
[    4.756528] cfg80211: Calling CRDA to update world regulatory domain
[    4.764277] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[    4.789296] usb 3-2: USB disconnect, device number 2
[    4.790818] usb 4-1: USB disconnect, device number 2
[    4.794119] usb 4-2: USB disconnect, device number 3
[    4.794530] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    4.794544] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    4.794567] ehci-pci 0000:00:1d.7: debug port 1
[    4.801826] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    4.801843] ehci-pci 0000:00:1d.7: irq 19, io mem 0xe4444000
[    4.814889] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    4.814982] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    4.814987] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.814991] usb usb5: Product: EHCI Host Controller
[    4.814995] usb usb5: Manufacturer: Linux 3.14.4-gnuowen ehci_hcd
[    4.814999] usb usb5: SerialNumber: 0000:00:1d.7
[    4.815566] Bluetooth: Core ver 2.18
[    4.815680] NET: Registered protocol family 31
[    4.815683] Bluetooth: HCI device and connection manager initialized
[    4.815697] Bluetooth: HCI socket layer initialized
[    4.815702] Bluetooth: L2CAP socket layer initialized
[    4.815719] Bluetooth: SCO socket layer initialized
[    4.815909] hub 5-0:1.0: USB hub found
[    4.815924] hub 5-0:1.0: 8 ports detected
[    4.831156] usbcore: registered new interface driver btusb
[    4.837548] hub 1-0:1.0: USB hub found
[    4.837567] hub 1-0:1.0: 2 ports detected
[    4.903055] hub 2-0:1.0: USB hub found
[    4.903080] hub 2-0:1.0: 2 ports detected
[    4.926593] hub 3-0:1.0: USB hub found
[    4.926612] hub 3-0:1.0: 2 ports detected
[    4.958905] ppdev: user-space parallel port driver
[    4.961754] ACPI: Battery Slot [BAT0] (battery absent)
[    4.962025] ACPI: Battery Slot [BAT1] (battery absent)
[    4.963139] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    4.963144] Bluetooth: BNEP filters: protocol multicast
[    4.963155] Bluetooth: BNEP socket layer initialized
[    4.964470] hub 4-0:1.0: USB hub found
[    4.964499] hub 4-0:1.0: 2 ports detected
[    4.965669] parport0: PC-style at 0x3bc (0x7bc)
[    5.013077] ath: phy0: Enable LNA combining
[    5.014613] ath: EEPROM regdomain: 0x60
[    5.014616] ath: EEPROM indicates we should expect a direct regpair map
[    5.014621] ath: Country alpha2 being used: 00
[    5.014623] ath: Regpair used: 0x60
[    5.059896] ACPI Warning: SystemIO range 0x00000528-0x0000052f conflicts with OpRegion 0x00000500-0x0000057f (\PMIO) (20131218/utaddress-258)
[    5.059908] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    5.059914] ACPI Warning: SystemIO range 0x000004b0-0x000004bf conflicts with OpRegion 0x00000480-0x000004bb (\GPIO) (20131218/utaddress-258)
[    5.059922] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    5.059925] ACPI Warning: SystemIO range 0x00000480-0x000004af conflicts with OpRegion 0x00000480-0x000004bb (\GPIO) (20131218/utaddress-258)
[    5.059932] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    5.059935] lpc_ich: Resource conflict(s) found affecting gpio_ich
[    5.060423] Non-volatile memory driver v1.3
[    5.063076] Bluetooth: RFCOMM TTY layer initialized
[    5.063094] Bluetooth: RFCOMM socket layer initialized
[    5.063104] Bluetooth: RFCOMM ver 1.11
[    5.085616] yenta_cardbus 0000:05:00.0: CardBus bridge found [0000:0000]
[    5.099137] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[    5.101081] thinkpad_acpi: ThinkPad ACPI Extras v0.25
[    5.101086] thinkpad_acpi: http://ibm-acpi.sf.net/
[    5.101089] thinkpad_acpi: ThinkPad BIOS CBET4000 7BETC7WW (2.08 ), EC 7BHT40WW-3.4
[    5.101092] thinkpad_acpi: Lenovo ThinkPad X60, model 1703WMF
[    5.103197] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xf9680000, irq=17
[    5.106112] thinkpad_acpi: detected a 8-level brightness capable ThinkPad
[    5.118050] usb 5-6: new high-speed USB device number 2 using ehci-pci
[    5.159699] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
[    5.162403] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input6
[    5.182266]  [PCSPP,TRISTATE]
[    5.182276] parport0: irq 7 detected
[    5.232783] usb 5-6: New USB device found, idVendor=17ef, idProduct=1000
[    5.232791] usb 5-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    5.233302] hub 5-6:1.0: USB hub found
[    5.233493] hub 5-6:1.0: 4 ports detected
[    5.239678] init: failsafe main process (671) killed by TERM signal
[    5.266041] lp0: using parport0 (polling).
[    5.266046] lp0: console ready
[    5.313448] yenta_cardbus 0000:05:00.0: ISA IRQ mask 0x0ca8, PCI irq 16
[    5.313457] yenta_cardbus 0000:05:00.0: Socket status: 30000006
[    5.313464] pci_bus 0000:05: Raising subordinate bus# of parent bus (#05) from #06 to #09
[    5.313476] yenta_cardbus 0000:05:00.0: pcmcia: parent PCI bridge window: [io  0x2000-0x3fff]
[    5.313481] yenta_cardbus 0000:05:00.0: pcmcia: parent PCI bridge window: [mem 0xe0000000-0xe20fffff]
[    5.313487] pcmcia_socket pcmcia_socket0: cs: memory probe 0xe0000000-0xe20fffff:
[    5.313501]  excluding 0xe1ef0000-0xe20fffff
[    5.313507] yenta_cardbus 0000:05:00.0: pcmcia: parent PCI bridge window: [mem 0xe2100000-0xe40fffff 64bit pref]
[    5.313512] pcmcia_socket pcmcia_socket0: cs: memory probe 0xe2100000-0xe40fffff:
[    5.313547]  excluding 0xe2100000-0xe40fffff
[    5.433731] hda_intel: probe_mask set to 0x1 for device 17aa:2010
[    5.433795] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[    5.454850] e1000e 0000:01:00.0: irq 45 for MSI/MSI-X
[    5.488680] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[    5.490154] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[    5.490527] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[    5.490674] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[    5.490811] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[    5.555702] e1000e 0000:01:00.0: irq 45 for MSI/MSI-X
[    5.556241] IPv6: ADDRCONF(NETDEV_UP): eth5: link is not ready
